The Hunter 59445 is the Dempsey 44-inch flush mount ceiling fan, sold in a New Bronze finish with four reversible composite blades in Mid Century Walnut on one side and Umber Walnut on the other. It uses a low-profile hugger bracket that sits directly against the ceiling with no downrod, making it a popular choice for rooms where clearance is limited. The fan ships with a wireless remote control that includes a receiver, a frosted glass globe bowl that twists into the light kit, and fully dimmable LED bulbs. When something on this fan needs replacing, the model number is your most important tool, and knowing which part numbers apply to the 59445 specifically will save you from ordering components that physically will not fit.
Hunter sells the Dempsey in several configurations across different model numbers, and the 59445 is one variant within that family. Some parts cross over between Dempsey models while others are specific to the 44-inch low-profile version. Before ordering anything, confirm the model number printed on the label inside the canopy cover where the fan mounts to the ceiling. The label will show 59445 and may include additional manufacturing details. That number is what you enter when searching on Hunter’s website, Amazon, or any third-party parts supplier to filter results to the right components.
Remote Control and Receiver Replacement
The wireless remote and its paired receiver are the most commonly replaced components on the 59445. The remote uses radio frequency communication, and when the fan stops responding to button presses, the problem is usually one of three things: dead batteries in the remote, a failed receiver inside the fan, or a remote that has lost its pairing and needs to be reset. Swapping the batteries is always the first step before assuming the remote itself has failed. The Hunter manual for the 59445 describes a specific pairing procedure where you turn the power off and back on at the wall switch, then hold the Fan Off button and the High button simultaneously for four seconds within three minutes of restoring power. If the fan responds normally after that, the remote is still functional and the pairing was just lost.
When the remote or receiver has genuinely failed, the replacement needs to match the frequency and channel configuration of the original. Hunter’s direct website at hunterfan.com carries replacement remote and receiver kits, and entering the model number 59445 in their parts lookup will show compatible options. ReplacementRemotes.com is another reliable source that specifically stocks remote control and receiver combinations for the Dempsey lineup and lists the 59445 by name. On Amazon, search for Hunter Dempsey remote and filter by compatibility with the 44-inch low-profile model to avoid receivers designed for downrod versions of the same fan series. The receiver typically mounts inside the canopy at the ceiling, connected between the house wiring and the fan’s internal wiring. Replacing it requires turning off power at the breaker, removing the canopy, disconnecting the receiver from both the ceiling wiring and the fan leads, and reconnecting the new unit following the color-coded diagram in the 59445 installation manual.
Fan Blades and Blade Brackets
The 59445 uses four 44-inch composite blades with the Mid Century Walnut and Umber Walnut reversible finish. Composite blades hold up better than wood in humidity but they can still warp, crack, or pick up damage that causes vibration and wobbling. A single damaged blade is enough to throw the fan out of balance, and replacing one blade while leaving the others can sometimes make the imbalance worse if the blades have aged unevenly. Hunter recommends replacing all four blades as a set when one has been damaged, which is straightforward with the 59445 because Hunter sells the complete blade set for this model.
The part number for the 59445 blade set is K564704575, and it is available through Hunter directly, through Ferguson Home, and through Amazon. When searching on Amazon, looking for Hunter Dempsey 44 blades Mid Century Walnut will surface compatible sets, but confirm the part number before purchasing because blades from other Dempsey variants with different spans or mounting configurations will not fit. The blade brackets on the 59445 connect the blades to the motor housing using standard screws, and the brackets themselves occasionally strip or crack at the mounting holes after years of use. Blade brackets for the Dempsey 44 are available on Amazon and through Hunter’s parts page and should be replaced as a set if more than one shows damage.
Glass Globe Replacement
The 59445 uses a frosted glass bowl that attaches to the light kit by twisting counterclockwise to position it over the tabs, then rotating clockwise until it locks. This twist-lock design makes the globe easy to install but also means it can work loose over time if it is not fully seated during installation or if the tabs wear down. Replacing a broken or cloudy globe is one of the more affordable repairs on this fan, and Hunter sells replacement globes through their website. The globe style on the 59445 is a standard frosted bowl shape that fits several Hunter light kits, but searching by the 59445 model number on hunterfan.com will confirm the correct fitting.
Third-party glass globes in the right diameter and opening size will also fit the light kit on this fan if Hunter’s OEM globe is out of stock or if you want a different aesthetic. The critical measurement is the opening diameter at the top of the globe where it meets the light kit fitter. Measure the existing globe before ordering a replacement from a third-party supplier. Amazon carries a range of ceiling fan glass globes in the appropriate sizes, and searching for Hunter Dempsey glass bowl or ceiling fan glass globe frosted bowl with the fitting diameter measurement will narrow results to compatible options.
LED Bulbs and Light Kit Components
The 59445 includes dimmable LED bulbs and a light kit with switch housing that connects below the motor. The LED bulbs in the stock configuration are designed to be fully dimmable and work with the remote’s dimming function, which adjusts output incrementally when you hold the light button. Not every LED bulb on the market is compatible with ceiling fan dimmers, and using a non-dimmable LED in the 59445 can cause flickering, buzzing, or failure to dim properly. When replacing bulbs, look specifically for dimmable LED bulbs in the correct base type and wattage listed in the 59445 manual, which also states the maximum wattage the light kit supports.
If the light kit itself fails rather than just the bulbs, Hunter sells switch housing and light kit components for the Dempsey. The light kit on the 59445 attaches to the lower switch housing using keyhole slots that wrap around screws and rotate to lock into place. The assembly screws that hold the upper and lower switch housings together need to be fully tightened during installation. A loose connection between the two housings is a common cause of lights flickering or failing to respond to the remote, and tightening those three screws is worth checking before assuming the light kit needs replacement.
Capacitor Replacement
The 59445 uses an AC motor, which means it has a run capacitor that regulates the speed of the fan. When the capacitor degrades, the fan will typically show one of a few specific symptoms: it runs only on one speed regardless of which button you press, it hums at certain speeds, it starts slowly and struggles to reach full speed, or it fails to start at all despite the remote responding normally. These are all signs that the capacitor has weakened or failed. The motor itself is rarely the problem when these symptoms appear.
Capacitors for the Hunter 59445 are usually available on Amazon and from PartSelect.com. The capacitor will have a microfarad rating printed on its casing, and the replacement must match that rating exactly. Using a capacitor with the wrong microfarad value will cause the fan to run incorrectly even if it starts and stops as expected. Accessing the capacitor requires removing the lower switch housing and the blades to reach the motor housing, then locating the capacitor, noting its wiring connections before disconnecting anything, and swapping the old unit for the new one. Take a photograph of the wiring configuration before disconnecting any leads so you have a reference during reassembly.
Where to Source Parts for the Hunter 59445
Hunter’s own website is the most reliable starting point for any part search. Their parts and manuals page at hunterfan.com lets you search by model number, and the 59445 will surface compatible remote kits, blade sets, glass globes, and light kit components that Hunter sells directly. Parts ordered from Hunter are guaranteed to be the correct fit, and Hunter’s customer service line at 1-888-830-1326 can help confirm compatibility if you are not sure which component you need.
Amazon is the most practical source for most owners because of pricing, availability, and the ability to read reviews from people who have used the same part on the same fan. When searching on Amazon, always include the model number 59445 or the Dempsey 44 in the search terms to avoid parts that fit different fans in the Hunter lineup. PartSelect.com and eReplacementParts.com both maintain searchable parts databases for Hunter fans, and both sites use model number lookups that will show a diagram of the 59445 with parts labeled so you can confirm you are looking at the right component before ordering. Ferguson Home carries the K564704575 blade set if you prefer to order from a home improvement supply source rather than a general retailer.
Lowe’s sold the 59445 when it was in production, and while they may no longer carry the fan itself, their parts and accessories section online sometimes shows compatible components. Hunter’s products sold through Lowe’s used the same parts ecosystem as the rest of the Hunter lineup, so anything listed as compatible with the Dempsey 44 on the Lowe’s website should fit the 59445 regardless of which retailer originally sold your specific fan.
Using the Model Number to Get the Right Part Every Time
The 59445 model number is on the label inside the canopy at the ceiling and may also appear on the original packaging if you still have it. Every parts supplier worth using will ask for this number, and providing it upfront avoids the back-and-forth of describing the fan by color, size, or style. Hunter’s Dempsey series spans multiple blade sizes and mounting configurations, and a part that fits the 52-inch downrod version will not necessarily fit the 59445’s 44-inch flush mount housing.
When a parts supplier does not have the 59445 in their database, searching for the Dempsey 44 low profile LED with the New Bronze finish will usually surface the same components since many suppliers index by product name rather than model number. The installation manual for the 59445 is available on Hunter’s website and through manualsfile.com, and it includes a parts diagram and list that identifies components by name and position, making it easier to describe exactly what you need when you are talking to a customer service representative or searching online.